How to Use Drawing Tools in PhotoDirector
Turn a product photo into a sale graphic with a label, a dark fade, and a hand-drawn circle.
Updated · 5 min read
In a hurry? Use the Drawing Tools quick guide instead.
PhotoDirector's drawing tools in the Design workspace add shapes, fades, and freehand marks to a photo, each on its own layer. Use them to turn a product shot into a sale post: a label from Shape, a dark fade from Gradient, and a hand-drawn circle from Pen. Your photo stays untouched underneath, so you can move or restyle each piece later.


- In PhotoDirector, choose Design from the launcher.
- Click Import > From Local Drive to open your photo.
- Click the Shape icon, pick the square, and drag on the photo. Set its size and Color in Shape Properties.
- Select the photo layer and press Ctrl+Shift+N for an empty layer. Drag a black-to-white Gradient from the bottom up, then set the layer's Blending mode to Multiply.
- Press Ctrl+Shift+N again, choose Pen > Brush, and draw around your subject.
- To recolor a stroke, select its layer and click the stroke with the Fill tool.
- Click Export, choose a format, and click Export again.
Steps to Use Drawing Tools in PhotoDirector
Step 1: Open Design
From the PhotoDirector launcher, choose Design. If layers are new to you, start with How to Use Layers in PhotoDirector.

Step 2: Import Your Photo
Under Import Photo, click the arrow on Import and choose From Local Drive to open your photo.

PhotoDirector asks whether to add a white layer beneath your image. Click No to keep just your photo, or Yes for a white base under it. The photo opens on its own layer. In this example, that layer is named Maple Photo.

Step 3: Draw a Label With the Shape Tool
Click the Shape icon in the left toolbar. The panel offers nine shapes, from a square and circle to stars and polygons. Pick the square, then drag on the photo where you want the label. PhotoDirector puts the shape on a new layer above your photo.

With the shape's layer selected, the panel turns into Shape Properties. Type a Width and Height that suit your photo. On this 5184-pixel-wide photo, the label is 1700 by 560 pixels. Click the Color swatch to pick a fill color, here a warm cream. In this example, the layer is named Sale Label.
Round corners stays off here. On a wide shape like this one, rounded corners stretch into ovals, so a plain rectangle gives the cleanest label. Merge Shapes stays gray until you select several shapes, so you can skip it for a single label.

To put words on the label, add a text layer above it with the Text tool. How to Add Text to Photos in PhotoDirector walks through it.
Step 4: Darken the Bottom With a Gradient
A darker bottom edge helps your label stand out. Select the photo layer and press Ctrl+Shift+N to add an empty layer, named Bottom Gradient in this example. Keep this layer under the label in the Layer Manager, or the fade darkens the label too.
Click the Gradient icon in the left toolbar. Under Select Gradient Type, choose the first type, a straight linear fade. Under Color, set black and white. Then drag on the photo from the bottom edge up to about the middle. If the dark end lands at the top, click the swap arrow between the two swatches and drag again.
In Normal mode, the white end washes out the top of your photo. To keep only the dark part, set the layer's Blending mode to Multiply at the top of the Layer Manager. Use the layer's setting, since the Gradient panel's own Blending mode doesn't change a gradient drawn on an empty layer. You can leave the panel's own Opacity and Blending mode as they are. Lower the layer's Opacity to soften the fade; this example uses 65.



Step 5: Circle Your Subject With the Pen
Press Ctrl+Shift+N again for a new empty layer, named Hand-drawn Circle here. Click the Pen icon in the left toolbar. Under Select tool, choose Pencil, Brush, or Air Brush. This example uses Brush.
Set the Size and click the Color swatch to pick a color. This circle uses Size 8 and the same cream as the label. Then drag one loop around your subject, and let the ends overlap a little so it looks hand-drawn. If the stroke looks jagged, press Ctrl+Z and redraw the loop in one steady motion.

Step 6: Recolor Strokes With the Fill Tool
To change a stroke's color later without redrawing it, use Fill. Select the layer with your strokes, then click the Fill icon, the paint bucket just below the Shape icon in the left toolbar. Click the Color swatch to pick the new color. Tolerance sets how closely a color must match the one you click to be filled. This example keeps it low, at 7. Then click a stroke.
This example practices on a separate new layer, Layer 1, with two cream Pencil strokes. That layer isn't part of the finished photo. With Contiguous selected, Fill changes only the stroke you click. Clear Contiguous, and Fill changes every matching color on the layer, so both strokes turn orange.



Step 7: Export Your Photo
Click Export at the top of the window.

In the Save Photo window, check the Export Destination and choose a Format, such as JPEG. Under Image Sizing, leave Keep original photo resolution selected. Or choose Resize to fit and enter a width and height. Then click Export.

The Result
The hand-drawn circle draws the eye to the leaf, and the label reads clearly against the darker bottom edge. Maple Photo itself never changed.

We tested these steps in PhotoDirector 365 version 18.0.10 on Windows.
Don't have PhotoDirector yet? Draw labels, fades, and hand-drawn marks on your photos, each on its own layer you can change later.
Download PhotoDirector Free →FAQ About Drawing Tools in PhotoDirector
When the full-size photo layer is selected, a drag on the canvas can move it instead of your shape. Right-click the photo layer in the Layer Manager and choose Lock Layer. Then select the layer you want to work on before you drag.
With the Shape tool open, select another layer in the Layer Manager, then select the shape's layer again. Shape Properties comes back, so you can change its Width, Height, or Color.
Export saves one flat photo. To keep every shape, gradient, and stroke on its own layer, also choose File > Save As and pick PHI files, then open that file in Design later.



