CyberLink Logo

How to Use Opacity, Fade, and Blending Modes in PowerDirector

Make logos and overlays sit naturally in your footage.

Updated Oct. 25, 2026 · 4 min read

PowerDirector's opacity, fade, and blending settings share one panel because each one controls how much of a clip you see. Opacity makes a clip see-through, a fade eases it in or out, and a blending mode mixes it with the clip on the track above. Use them when an overlay looks pasted on or a clip should ease in, not pop.

⚡ Quick Answer: How to Use Opacity, Fade, and Blend in 6 Steps
  1. Select a clip and click Edit above the timeline, then choose Opacity / Fade / Blend in the Tools list. Or double-click the clip to open the Edit panel.
  2. Drag the Opacity slider. Or drag the white line across the clip on the timeline to change the same setting.
  3. Check Fade-in or Fade-out.
  4. Drag the white keyframe dots on the clip to change how long the fade lasts.
  5. Put the overlay on the track below your footage, then select the overlay.
  6. Pick a Blending Mode to mix the clip with the one on the track above it.

Steps to Set Opacity, Fade, and Blending

Prefer to watch? Here's the whole thing in a 3-minute video, or follow the written sections below.

Step 1: Open the Opacity / Fade / Blend Panel

Select the clip on the timeline and click Edit in the toolbar above the timeline to open the panel at the top left. Or double-click the clip. Under the Image or Video tab, click Opacity / Fade / Blend in the Tools list. The opacity, fade, and blending settings all sit on that one screen.

The Edit button in the toolbar above the timeline, with a clip selected
Click Edit, or double-click the clip.
The PowerDirector Edit panel with Opacity / Fade / Blend selected in the Tools list
One panel holds all three settings.

Step 2: Set How See-Through the Clip Is

Drag the Opacity slider. Or type a number in the box beside it. The lower the value, the more you see through to whatever is underneath.

Lower it when a logo or watermark is shouting louder than the footage it sits on. Lowering it also keeps a background readable through the clip on top.

The Opacity slider in the Edit panel, highlighted
Drag it, or type the number straight in.

There's also a faster way that skips the panel. Every clip on the timeline has a thin white line running across it. Hover over the line until the cursor changes, then drag up or down.

The white opacity line across a clip on the timeline, with the drag cursor showing
Or drag the white line on the clip.

Step 3: Turn On a Fade-in or Fade-out

A fade is a clip appearing or disappearing gradually instead of cutting. In the same panel, under Fade, check Fade-in to ease the clip in at its start, Fade-out to ease it out at the end, or both.

The Fade-in and Fade-out checkboxes under Fade in the Edit panel
Two checkboxes, one for each end of the clip.

Step 4: Set the Fade Length

Checking the box gives you a fade of a default length. To change how long it lasts, drag the white keyframe dots that appear on the clip itself. Pull one farther into the clip and the fade takes longer. Pull it back toward the edge and the fade gets shorter.

A white fade keyframe dot on a timeline clip, highlighted
Drag the dot to make the fade longer or shorter.

Other Ways to Add a Fade

PowerDirector gives you three ways to add a fade, and they all end up looking the same. Which one to use depends on what else you want from it:

WhereWhat you doReach for it when
Opacity / Fade / BlendCheck Fade-in or Fade-out, then drag the keyframe dotsYou just want a fade. This is the shortest route and the only one that lets you set the length by dragging on the clip
Animation tabClick the Animation tab at the top of the Edit panel, then pick Fade under In or OutYou're already choosing an entrance or exit for the clip and want the fade next to the other animations
Transitions libraryOpen the Transitions tab of the library, search for Fade, and drag it onto the clipThe fade belongs between two clips. Dropped on the start or end of a single clip, it fades that clip in or out too
The Animation tab at the top of the Edit panel, with Fade selected under In
The Animation tab route, alongside the other entrances.
The Transitions tab of the library with Fade being typed in the search box
The Transitions route starts with a search for Fade.

Drop the Fade transition on the start of a clip with nothing before it, and the clip fades in.

The Fade tile boxed in the PowerDirector Transitions library, and the Fade transition boxed at the start of the Skateboard 01 clip on the timeline, with nothing before the clip and a tooltip showing a one-second duration.
On the start of a single clip, Fade fades the clip in.

Step 5: Stack the Clips for Blending

A blending mode mixes the selected clip with the clip on the track above it, so that track needs a clip at the same point in time. Use one when you want a light leak, a grain overlay, or a gradient mixed into your footage instead of simply laid on top. Put the overlay on the track below your footage, then select the overlay.

Two clips stacked on the timeline, with the blend relationship marked between them
The selected clip blends with the one on the track above.

Step 6: Pick a Blending Mode

Open the Blending Mode dropdown below the fade checkboxes and pick one. Each mode combines the two clips by a different rule. The fastest way to choose is to click through them and watch the preview window.

The Blending Mode dropdown open in the Edit panel
Click through them and watch the preview.

Compare two of them to see how far apart the results can be. Darken keeps the darkest pixels of the two clips, so it thins out anything bright and reads as subtle. Difference subtracts one from the other, and the result looks like a color negative that's much harder to miss.

The same footage shown with Darken and with Difference side by side
The same two clips in two modes give very different results.

We tested these steps in PowerDirector 365 versions 23.4 and 25.0.10 on Windows.

Don't have PowerDirector yet? Opacity, fade, and blending share one panel, so trying all three takes about as long as reading this.

Download PowerDirector Free →

FAQ About Opacity, Fade, and Blending Modes

A blending mode mixes the selected clip with the clip on the track above it, so it needs something up there to mix with. If your clip is on the top track, or the track above is empty at that point on the timeline, every mode will look identical. Put the overlay on the track below your footage, select the overlay, and pick the mode there.

Use the checkboxes in Opacity / Fade / Blend for most fades. They're the quickest route, and you set the fade's length by dragging the keyframe dots on the clip. If you're already picking an entrance for the clip, use the Animation tab. Pick a Transition when the fade belongs between two clips, though it also works on the start or end of a single clip.

No. Opacity, fades, and blending modes are all project settings applied while the clip plays, so the media in your library is untouched. Set the opacity back to 100% and the clip is exactly as it was.